Creality Ender-3 V3 Ceramic Heating Block Kit

Your Ender-3 V3 was halfway through an overnight print when the screen threw a "nozzle not heating as expected" error. The temperature reading sits at room temperature, the print is ruined, and the machine you rely on is now a very expensive paperweight until the hotend is sorted.

This genuine Creality ceramic hotend heating kit (Creality part 4001030134) is the factory replacement for the Creality Ender-3 V3 and Creality Ender-3 V3 Plus. It arrives with the ceramic heater, thermistor, silicone sock and quick-swap nozzle already assembled, so you replace the whole heating chain in one go instead of chasing individual faults.

The headline benefit: your printer goes back to full 300 °C, 32 mm³/s performance with an OEM part that fits exactly like the original.

Genuine Creality OEM part | Fits Ender-3 V3 and V3 Plus | 60 W 360° ceramic heater | 200 °C in about 40 seconds | Up to 300 °C | 32 mm³/s max flow | Quick-swap tri-metal nozzle included

Who the Creality Ender-3 V3 ceramic hotend kit is built for

The hobbyist Maker who wants the printer working again tonight

You bought an Ender-3 V3 to print, not to troubleshoot. When the heater cracks or the thermistor fails, this kit removes the guesswork, because every heating component is new and matched at the factory. You swap one assembly, run a test heat-up and carry on. A realistic outcome: order today, fit the kit when the courier arrives, and restart that tabletop terrain set the same evening without hunting for loose wires or mismatched parts.

The small print farm operator protecting uptime

On a farm of CoreXZ machines, a failed hotend costs you printer hours, not just a part. Keeping one complete kit on the shelf per handful of Ender-3 V3 units means you swap the assembly in minutes and diagnose the faulty one on the bench later. Because the kit is identical to the factory unit, your sliced profiles, flow calibration and speed settings carry straight over, so a batch of 40 enclosure clips continues at the same quality after the swap.

The school technician keeping a lab of printers running

Classroom printers see clogs, crashed nozzles and the occasional curious screwdriver. A complete pre-assembled heating kit lets a technician restore a printer between lessons without specialist soldering or crimping. The quick-swap nozzle also means a blocked nozzle no longer takes the whole hotend out of service. Fit the kit during a free period and the Grade 10 design class can print their bracket projects that afternoon.

What sets this Creality Ender-3 V3 ceramic hotend kit apart

Heat-up times that keep you printing, not waiting

A conventional cartridge heater warms the block from one side. This kit uses a 60 W ring-shaped ceramic heater that wraps 360° around the melt zone, so heat enters evenly from every side. In practice the hotend reaches 200 °C in about 40 seconds. Even heating also means a more stable melt temperature at high flow rates, which shows up as consistent extrusion width on fast perimeters. For anyone running several short jobs a day, those saved minutes per heat-up add up quickly across a week.

Flow headroom for the speeds your printer was designed for

The Ender-3 V3 is rated for 600 mm/s, and that figure only means something if the hotend can melt plastic fast enough. This kit is rated for a maximum volumetric flow of 32 mm³/s, matching the original specification, thanks to an enlarged nozzle melt chamber. Fitting a generic hotend with a lower flow ceiling forces you to slow down every profile in your slicer. With the genuine part, your existing Creality Print or OrcaSlicer profiles stay valid.

A nozzle built to last, and to swap in seconds

The quick-swap nozzle uses a tri-metal construction: a copper alloy body for heat transfer, a hardened steel tip for wear resistance and a titanium alloy heatbreak to stop heat creeping up into the extruder. The hardened tip lets you print carbon fibre filled filaments without wearing the orifice oval within a few spools. When a nozzle does block, you replace the nozzle alone rather than the whole kit, which keeps running costs down.

Accurate temperature reading from the first heat cycle

The kit includes a new thermistor already seated in the block. A thermistor that has been pulled, kinked or overheated often reads a few degrees off, which leads to stringing, poor layer adhesion or false heating errors. Starting with a matched heater and sensor pair gives the firmware a clean reference. After fitting, run a heat-up test and a short calibration print before returning to production jobs.

Make sure you order the right kit for your printer

Creality uses several similar-looking ceramic kits across its range, and the wiring and mounting differ. Use the table below before you order.

Full specifications

Ordering, shipping and support for your Ender-3 V3 hotend kit

We courier this kit to any address across South Africa from our Centurion and Boksburg stores, where you can also collect in person. Manufacturing defects are handled locally through our technical support ticket system, so you never deal with an overseas return. While you order, stock up on Creality PLA filament or browse more Creality spare parts.

Frequently asked questions

Will this hotend kit fit my Ender-3 V3 SE or Ender-3 V3 KE?

No, this kit fits only the Ender-3 V3 and Ender-3 V3 Plus. The Ender-3 V3 SE and Ender-3 V3 KE use a different toolhead, wiring and mounting, and Creality sells separate kits for them. Check the part number table above, or browse our hot ends range to find the matching kit.

Can it print carbon fibre filled filaments?

Yes, the hardened steel nozzle tip is designed to resist the wear caused by PLA-CF and PETG-CF. With a 300 °C ceiling the kit also handles ABS and ASA comfortably. Dry abrasive filaments before printing, and consider a larger nozzle for heavily filled materials to reduce clogging. You will find suitable materials in our speciality filament range.

How long does it take to fit?

Most owners fit the kit in well under an hour with basic hand tools. Remove the front toolhead cover, unplug the heater and thermistor connectors, release the old assembly and fit the new one in reverse order. Some connectors on the toolhead board are secured with hot glue, so work gently. Finish with a heat-up test and a short calibration print.

My printer shows error Key:2564, will this kit fix it?

Often yes, because this error usually points to a failed ceramic heater or thermistor, both of which this kit replaces. Owners on the Creality forum report the same fault cleared after a hotend swap. Before ordering, check that the heater and thermistor plugs are seated and that the toolhead cable in the drag chain is not pinched, since a damaged cable produces the same message.

Is there local support if the kit is faulty?

Yes, any manufacturing defect is handled locally by our South African support team. Log a ticket with your order number and a short description or video of the fault, and our technicians will guide you through testing before arranging a replacement. There is no need to return the part to Creality overseas.