Anycubic Photon P1 FEP Film (Pack of 2)

A clouded or punctured release film usually shows up at the worst moment, halfway through a batch of parts you needed finished today. On most resin printers that means stretching a fresh sheet of loose film over a metal ring and fighting to get the tension even before you can print again. The Anycubic Photon P1 skips that step entirely, but only if you are fitting the film it was actually designed around.

This pack of two genuine NFEP films arrives pre-framed and pre-tensioned, so replacing a worn film is a straight swap rather than a tensioning job. You get a fresh, low peel-force surface back in the vat in minutes, with a spare on hand for the next time.

NFEP (PFA) Film Chemistry | Pre-Framed & Pre-Tensioned | 95% Light Transmittance | 0.15 mm Thickness | Sized for the P1's 10.1-Inch Screen | Pack of 2 | Genuine Anycubic Spare Part

Who the Anycubic Photon P1 FEP Film (Pack of 2) is built for

Prototyping engineers and small business owners

A punctured or clouded film mid-batch is a lost job, not just a lost print. Keeping a spare pack of pre-tensioned NFEP film on the shelf means a damaged film gets swapped in minutes instead of stalling a deadline while you source a replacement, for example finishing an overnight run of engineering brackets without losing the shift to a film failure.

Small print farm operators

Running several Photon P1 units means film wear is a constant line item, and traditional loose FEP sheets add a tensioning step every single swap. Because this film is pre-framed, changeovers between jobs stay fast across a fleet of machines, which matters when downtime on one printer means a backlog on the rest.

Hobbyist makers who print detailed miniatures

Fine supports and thin details are the first thing to suffer once a film's surface degrades or clouds over with use. Fitting a fresh NFEP film restores the low peel-force release that protects delicate geometry during separation, useful before a big batch of tabletop miniatures where a torn support halfway through the print ruins the whole plate.

What sets the Anycubic Photon P1 FEP Film (Pack of 2) apart

A film swap that skips the tensioning ritual

Unlike a traditional loose FEP sheet that needs stretching evenly across a metal ring, this film comes pre-framed and pre-tensioned from the factory. You lift the old film out of the vat and drop the new one straight in, with no risk of an uneven stretch causing inconsistent curing across the build plate.

Chemistry built to protect fine details

NFEP, a PFA-based film, has a measurably lower peel-force coefficient than standard FEP. That translates directly into less stress pulling on thin supports and fine miniature detail during each layer's separation, and less strain on the vat's seals over the film's working life.

Clarity that keeps curing accurate

At roughly 95% light transmittance, the film lets UV light through with minimal scatter, which keeps the P1's cure times and layer accuracy consistent with the printer's factory-calibrated exposure profiles. A clouded or aged film cuts that transmittance, which is usually the first sign it needs replacing.

Thickness tuned for durability and light transmission

At 0.15 mm, the film is thick enough to resist punctures from stray support tips or scraper contact, while staying thin enough not to compromise UV transmission or add noticeable curing lag. It is the same thickness Anycubic specifies for the P1's factory film, so exposure settings do not need adjusting after a swap.

Sized precisely for the P1's screen, not a generic cut

The film is cut and framed to match the Photon P1's 10.1-inch LCD exactly, rather than a generic size that needs trimming. That precision fit is what keeps the vat sealing correctly against the frame and stops resin creeping around the edges during a long print.

Two films, one order, less time waiting on a reorder

Buying the pack of two rather than a single film means the next failure does not turn into a delivery wait. The moment one film starts showing reduced release performance or visible clouding, you fit the spare immediately and keep printing, then reorder on your own schedule rather than mid-job. For anyone running the P1 commercially, that spare is effectively insurance against a day of downtime.

Full specifications

How the Anycubic Photon P1 FEP Film compares to the rest of the Photon range

Materials and software

Resins this film handles

• Standard UV resin: runs at the P1's default exposure settings with no adjustment needed after fitting a fresh film.
• High-viscosity engineering resin (up to 8000 cps): the NFEP chemistry's lower peel force helps thicker resins release cleanly layer after layer, reducing the drag that thick resin puts on a standard FEP surface.
• Tough and ABS-like resin: benefits most from the reduced peel force on wide, flat-bottomed prints, where separation forces are highest and most likely to cause warping or cracking.
• Flexible or TPU-like resin: prints cleanly on this film, though flexible parts can leave more residue behind than rigid resins, so wipe the film down between material changes.

Slicers and software

The Photon P1 pairs this film with Anycubic's Photon Workshop exposure profiles, which are calibrated to the film's factory thickness and transmittance, so no manual exposure recalibration is needed after a swap. The printer also works with Chitubox, Lychee Slicer, and Tango, though third-party slicers should still use Anycubic's published exposure values for this film when dialling in new resin profiles.

What's in the box

• 2 x Anycubic Photon P1 NFEP Film, pre-framed and pre-tensioned
• Protective film layers on both sides for handling
• Fitment instructions

Ordering, shipping and support

We ship this film pack nationwide by courier from our Centurion and Boksburg stores, with local warranty handling if a manufacturing fault turns up, no need to arrange an overseas return. If you also run an Anycubic Photon P1 and need other Anycubic spare parts, both are stocked locally alongside this film.

Frequently asked questions

Is this NFEP film different from a standard FEP film?

Yes. NFEP is a PFA-based film with a lower peel-force coefficient than standard FEP, which reduces the strain on fine details and support structures during layer separation. It also arrives pre-framed and pre-tensioned, unlike a loose FEP sheet that needs stretching over a ring by hand.

Does this film work with high-viscosity or engineering resin?

Yes. The P1 is rated for resins up to 8000 cps, and this film's low peel-force chemistry is part of what makes thicker resins release cleanly at that viscosity without excessive drag on the build plate.

How long does it take to fit this film?

A few minutes. Because the film is pre-framed and pre-tensioned, you lift the worn film out of the vat and drop the new one straight in, with no manual stretching or tensioning step required.

How often does the film need replacing?

It depends on print volume and resin type, but most users notice reduced release performance, more resistance during peel, or visible clouding after several hundred layers of continuous use, sooner with pigmented or high-viscosity resins. Keeping a spare pack on hand avoids a mid-batch scramble when that point arrives.

Does this film come with local warranty support in South Africa?

Yes. As a genuine Anycubic part sold through our Centurion and Boksburg stores, it is covered by local warranty handling, so a manufacturing fault is resolved here rather than through an overseas return process.